Windows vista net time

Best eReaders. Best VPN. Browse All News Articles. Baby Shark YouTube. Venmo Gifts. Fortnite iPhone. Quest Headset SteamVR. M1 Mac Dropbox. Windows 11 Uninstall Clock. Teams Walkie-Talkie. PCI Express 6. Use Your iPhone as a Webcam. Hide Private Photos on iPhone. All Microsoft's PowerToys for Windows. Take Screenshot by Tapping Back of iPhone. The following table lists the policies that you can configure for the Windows Time service, and the registry subkeys that those policies affect.

When you remove a Group Policy setting, Windows removes the corresponding entry from the policy area of the registry. This information is provided as a reference for use in troubleshooting and validation. Windows registry keys are used by W32Time to store critical information. Don't change these values.

Modifications to the registry are not validated by the registry editor or by Windows before they are applied. If the registry contains invalid values, Windows may experience unrecoverable errors. Some of the parameters in the registry are measured in clock ticks and some are measured in seconds. To convert the time from clock ticks to seconds, use these conversion factors:.

Note Zero is not a valid value for the FrequencyCorrectRate registry entry. HoldPeriod All versions Controls the period of time for which spike detection is disabled in order to bring the local clock into synchronization quickly. A spike is a time sample indicating that time is off a number of seconds, and is usually received after good time samples have been returned consistently.

The default value on domain members is 5. The default value on stand-alone clients and servers is 5. LargePhaseOffset All versions Specifies that a time offset greater than or equal to this value in 10 -7 seconds is considered a spike. A network disruption such as a large amount of traffic might cause a spike. A spike will be ignored unless it persists for a long period of time.

The default value on domain members is The default value on stand-alone clients and servers is It contains reserved data that is used by the Windows operating system, and any changes to this setting can cause unpredictable results.

MaxAllowedPhaseOffset All versions Specifies the maximum offset in seconds for which W32Time attempts to adjust the computer clock by using the clock rate.

When the offset exceeds this rate, W32Time sets the computer clock directly. The default value for domain members is The default value for stand-alone clients and servers is 1.

The default value for stand-alone clients and servers is MaxNegPhaseCorrection All versions Specifies the largest negative time correction, in seconds, that the service makes. If the service determines that a change larger than this is required, it logs an event instead. This value means that the service always corrects the time. The default value for domain controllers is , 48 hrs.

The default value for stand-alone clients and servers is 54, 15 hrs. MaxPollInterval All versions Specifies the largest interval, in log2 seconds, allowed for the system polling interval. Note that while a system must poll according to the scheduled interval, a provider can refuse to produce samples when requested to do so.

The default value for domain controllers is MaxPosPhaseCorrection All versions Specifies the largest positive time correction in seconds that the service makes. MinPollInterval All versions Specifies the smallest interval, in log base 2 seconds, allowed for the system polling interval.

Note that while a system does not request samples more frequently than this, a provider can produce samples at times other than the scheduled interval. The default value for domain controllers is 6. PhaseCorrectRate All versions Controls the rate at which the phase error is corrected. Specifying a small value corrects the phase error quickly, but might cause the clock to become unstable. If the value is too large, it takes a longer time to correct the phase error.

The default value on domain members is 1. The default value on stand-alone clients and servers is 7. Note Zero is not a valid value for the PhaseCorrectRate registry entry. PollAdjustFactor All versions Controls the decision to increase or decrease the poll interval for the system.

The larger the value, the smaller the amount of error that causes the poll interval to be decreased. RequireSecureTimeSyncRequests Windows 8 and later versions Controls whether or not the DC will respond to time sync requests that use older authentication protocols. If enabled set to 1 , the DC will not respond to requests using such protocols.

This is a boolean setting, and the default value is 0. SpikeWatchPeriod All versions Specifies the amount of time that a suspicious offset must persist before it is accepted as correct in seconds. The default value on stand-alone clients and workstations is TimeJumpAuditOffset All versions An unsigned integer that indicates the time jump audit threshold, in seconds.

If the time service adjusts the local clock by setting the clock directly, and the time correction is more than this value, then the time service logs an audit event. UpdateInterval All versions Specifies the number of clock ticks between phase correction adjustments. The default value for domain members is 30, The default value for stand-alone clients and servers is , Note Zero is not a valid value for the UpdateInterval registry entry.

The default value on stand-alone clients and servers is 1. The default value on stand-alone clients and servers is 0x1. The NtpServer is a time server that responds to client time requests on the network by returning time samples that are useful for synchronizing the local clock. LargeSampleSkew All versions Specifies the large sample skew for logging, in seconds. Events will be logged for this setting only when EventLogFlags is explicitly configured for 0x2 large sample skew.

The default value on domain members is 3. The default value on stand-alone clients and servers is 3. Why should I install the Microsoft Download Manager? In this case, you will have to download the files individually. You would have the opportunity to download individual files on the "Thank you for downloading" page after completing your download. Files larger than 1 GB may take much longer to download and might not download correctly.

You might not be able to pause the active downloads or resume downloads that have failed. Back Next. Details Version:. File Name:. Brian Kelley 8, 30 30 silver badges 33 33 bronze badges. Christopher Edwards Christopher Edwards 1 1 gold badge 8 8 silver badges 19 19 bronze badges. MikeJ MikeJ 1, 3 3 gold badges 13 13 silver badges 24 24 bronze badges. Sign up or log in Sign up using Google. Sign up using Facebook. Sign up using Email and Password. Post as a guest Name.

Email Required, but never shown. The Overflow Blog. Stack Gives Back Safety in numbers: crowdsourcing data on nefarious IP addresses. Featured on Meta.